Search in blog

Blog categories

View all categories

Popular posts

Properties of Common Solvents

Posted in: Tank Cleaning, Paint and Coatings, Tables and Conversions

07/19/2014

Density, boiling point, evaporation rate, and flash point of common solvents

Tip Speed Definition and Formula

Posted in: Mixing and Dispersion, Toolbox

10/16/2012

Blade Speed (tip speed), measures how far a point on the outer most edge of the disperser blade travels in a given...

CLEARANCE HOLE CHART

Posted in: Tables and Conversions

06/20/2022

Clearance hole chart for inch bolts and screws according to ASME B18.2.8

Paint Formulation

Posted in: Paint and Coatings

10/19/2020

Paint consists of four basic components: Resin Pigment Solvent Additives The performance of a coating is influenced...

Viscosity Conversion

Posted in: Mixing and Dispersion, Tables and Conversions

11/06/2021

Viscosity Conversion table comparing some of the typical viscosity scales used in Paint and Coatings including:...

View all popular posts

Latest comments

Tim Franklin on Paint Formulation

★★★★★ (5.0)

Blade to mix sand into paint
Used to have a Teflon on plastic blade need one for my...
PRASANTA DATTA on Paint Formulation

★★★★★ (5.0)

cpvc and paint mix formula
very good excellent OK
STEVE HARRISON on Paint Formulation

★★★★★ (5.0)

Paint Formulation for my startup
I would like you to share with me paint formula with...
Francis on Paint Formulation

★★★★★ (5.0)

Formula application
Thanks so much for formulation offered but I wish it be...
Mushahid Hussain on Paint Formulation

★★★★★ (5.0)

Formulation
Need all types of paint formulations

View all comments

Blog RSS

Posted in: "2021"

Sort by:

LOUVERED BLADE MOUNTING CONSIDERATION

Posted in: Mixing and Dispersion

1871 Views 0 Liked

Beyond impeller bore configurations, with the Conn styles as well as other louvered or vented styles open area in the center of the impeller must also be considered. Typically, reinforcing discs, taper plates, sandwich the blade to stiffen the disperser disc. Due to the louver placement on the conn blade, the size of these disks, and with small sizes - the diameter of the mounting hub must be considered.

Read more
DISPERSER CONFIGURATION

Posted in: Mixing and Dispersion

13645 Views 0 Liked

The design of a dispersion system begins by defining the batch size and product characteristics. From there we can begin to determine blade size, types, and number which will then allow us to define shaft rpm and horsepower requirements.

Read more
Filling Equipment - Request for Quotation (RFQ)

Posted in: Filling and Packaging, Request For Quotation

3212 Views 0 Liked

Ideal-Pak Request for Quotation is designed to gather pertinent information for your filling project to allow us to make the best possible recommendations. Provide details of your filling requirements including; product characteristics, containers details, fill speeds, and accuracies so we can provide a solution to meet your needs.

Read more
2021 Pack Expo Las Vegas, Sept 27-29

Posted in: Events

3092 Views 0 Liked

PACK EXPO Las Vegas and Healthcare Packaging EXPO are co-located shows at the Las Vegas Convention Center. Your badge allows you to move freely from one show to the other among the South, Central and North halls.

Read more
What to consider when moving to an Inverter

Posted in: Mixing and Dispersion, Electrical

3419 Views 0 Liked

Inverters offer many benefits over traditional mechanical drives with fewer moving parts, larger speed ranges, broader horsepower range, and reduced maintenance. But they do have limitations the largest of which is their torque characteristics. sss

Read more

|<<12

Showing 13 to 17 of 17 (2 Pages)